An Easy Instruction for Installing a Bathtub
An Easy Instruction for Installing a Bathtub
Blog Article
The writer is making a number of good pointers on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in the content further down.
Setting up a bathtub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately tough project. If the old tub is conveniently easily accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub as well as position the new bathtub, the job is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Make certain you have actually certified yourself for the task and also fit trying it. Rather than hiring a specialist to take over a halfway-completed project, it is far better to think about using one prior to you start. Chances are you may need a professional plumber to make tube links.
This short article will assist you set up a brand-new bath tub in your bathroom if you have currently purchased a new tub as well as do not need to transform the plan of your previous water supply pipelines.
Your devices as well as product list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to see to it that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to prevent strain on the tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is detach the water. After doing so, switch on the faucets to drain any type of water staying in the system. The process of eliminating the existing taps can be rather troublesome due to the restricted accessibility that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. Once the supply pipes have been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, place the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water system and examine all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the tub and additionally inspect the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub must wait till the bath tub has actually been utilized at least when as this will settle it right into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making certain that the washers are in location in between the faucet as well as the sink. Secure the tap in place with the maker supplied backnut. Once the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The former type must be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about issues with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the tub with water before securing, to permit the activity experienced when the bathtub is in usage. The sealant can crack rather very early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very eager about A Step-by-Step Guide to Installing a Bathtub and I am praying you enjoyed reading our blog post. If you appreciated our page kindly do not forget to share it. Thank you so much for taking the time to read it.
Immediate help? Ring! Report this page